Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Pearland Homeowners Choose Gelco Chimney Cleaning
We provide independent Gelco chimney cleaning service in Pearland, and our technicians work on Gelco caps, tops, and venting components as part of a full sweep-inspection-repair visit. What makes our Gelco work different is that it isn’t a sales call. We inspect first, then recommend, and the cap gets cleaned, reseated, or replaced only when the evidence on your chimney shows it needs it. Pearland Chimney Cleaning is not affiliated with or authorized by Gelco; we’re an independent service provider, and we say so plainly.
Gelco is a chimney cap brand. That’s a narrow product category, but caps are where a lot of Pearland chimney problems start, and they’re the part most sweep-only companies never look at twice. We do. Call (866) 361-9474 and we’ll book a sweep. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Pearland Chimney Cleaning for Your Gelco Chimney Cleaning?
Our technicians have up to 15 years of experience, and a good share of that has been spent on Gelco caps in the field rather than reading spec sheets. That matters because Gelco caps fail in specific ways you can only learn by pulling them off a flue: rusted seams, clogged screens, brackets that have quietly let go. When we walk up to a Gelco Multi-Flue Cap or a Gelco Vent Top in Pearland, we usually have a pretty good idea what we’re going to find before we touch it.
We fit quality parts to Gelco equipment. That means OEM-equivalent replacement caps, screens, and mounting hardware when it’s available, and high-grade stainless aftermarket components when it isn’t. Nothing generic from a hardware store shelf goes onto your flue, and we won’t sell you a whole new cap when a screen swap would do.
Service is warranty-safe. We work carefully around the existing cap, note its condition in writing before and after, and document everything so you have a record if a warranty question ever comes up. Inspections are suitable for real estate transactions, insurance documentation, and annual safety compliance. One call covers sweep, inspection, and repair, and the same company that cleans your flue fixes what it finds. No handoffs. No second-contractor gap.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common Gelco Chimney Cleaning Problems We Fix in Pearland
These are the issues we run into most often with Gelco products in Pearland, and each one has a cause worth understanding.
- Rusted seams and pinholes. Stainless or galvanized Gelco caps develop rusted seams and pinholes after years of Gulf Coast humidity, and once a seam opens, water drips straight down the flue. The cap still looks fine from the yard. The damage is happening underneath.
- Clogged screens and spark arrestors. Cap screens and spark arrestors mat up with creosote and soot, which restricts draft and makes the fireplace burn smoky. A clogged screen is also the reason a fire can back up into the room instead of going up the flue.
- Loose or missing mounting screws and brackets. Wind works cap fasteners loose over time. A loose bracket lets wind-driven rain enter the flue, and a cap that’s shifted off-center is a cap that isn’t sealing anything.
- Caps sized wrong for the flue tile. A Gelco cap that was sized incorrectly for the flue leaves gaps at the edges, and those gaps invite birds, squirrels, and water intrusion. A wrong-size cap is worse than a modest one, because it gives the impression of protection it doesn’t provide.
- Untouched creosote and wildlife nests underneath. In the newer Shadow Creek Ranch and Silverlake subdivisions, many fireplaces are decorative gas or prefab units that get little use, so years of creosote and the occasional bird or wasp nest sit undisturbed under a cap nobody has checked. The cap is fine. What’s under it isn’t.
How a typical job tends to go: a homeowner notices water stains on the firebox ceiling and a smoky smell after rain, and inspection usually reveals a Gelco multi-flue cap with rusted-through seams or a missing screen panel. The fix is normally a direct-fit stainless cap replacement with new mounting brackets and a bead of high-temp sealant, which restores draft and keeps rain and animals out of the flue.
Gelco Parts & Our Repair-vs-Replace Approach
We source OEM-equivalent Gelco replacement caps, screens, and mounting hardware when it’s available, and high-grade stainless aftermarket components when OEM parts are discontinued or backordered. We don’t claim to stock genuine Gelco parts, and we won’t tell you we do.
Repair versus replace comes down to remaining cap life. A cap with surface discoloration and intact seams usually gets cleaned, reseated, and a new screen. A cap with rusted-through metal, a bent frame, or brackets that no longer hold tension has reached the end of what any repair can do, and we’ll say so and show you why. If the metal is still sound and the problem is fasteners or a screen, we tell you it can wait or that a small repair is enough. If it isn’t, you’ll see the rust yourself before we recommend anything.
That’s the whole approach: we identify it, we fix it. If you want a straight answer on your cap, call (866) 361-9474 for a free estimate.
Our Gelco Service Process – Step by Step
- 1
Diagnosis. We start on the roof with the cap itself, checking seams, screens, fasteners, and the fit against the flue tile. Then we sweep the flue and run a camera so we can see what the cap has or hasn’t been protecting.
- 2
Repair or install. If the cap can be saved, we clean it, replace the screen or hardware, reseat it with new brackets, and seal it with high-temp sealant. If it can’t, we install a direct-fit replacement sized to the actual flue opening, not the nearest stock size.
- 3
Test. We verify draft and check for water paths around the cap, then confirm the fireplace draws the way it should before we leave.
- 4
Documentation. You get a photo report of what we found and what we did, which is the piece that matters if a warranty claim or an insurance question ever comes up.
See the difference
Before
After
Before
After
Before
AfterGelco Products We Service & Install in Pearland
The Gelco line we work with is cap and top work, and that’s what we service in Pearland: Gelco Multi-Flue Caps, Gelco Custom Stainless Caps, Gelco Single-Flue Caps, and Gelco Vent Top and Chase Covers. Multi-flue caps are the most common in this area’s subdivisions, since they cover the multiple flue tiles that come with prefab and builder-grade fireplace construction. Single-flue caps show up on older or simpler stacks. Custom stainless caps come into play where a flue opening is an odd size, and vent tops and chase covers handle the pre-fabricated chase enclosures common on newer homes. Cap replacement and cap installation are two of the most frequent jobs we do on Gelco equipment, and each one starts with measuring the flue opening rather than guessing at it.
We Also Service These Brands
Pearland Chimney Cleaning works across six professional-grade brands: DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, and Copperfield. DuraFlex and HeatShield are the two we lean on most for liner restoration and relining, which matters when a cap failure has let water into a flue long enough to damage the liner underneath. We’re not locked into one brand, so the recommendation follows your chimney instead of our inventory.
FAQs – Gelco Chimney Cleaning Service in Pearland
No. We’re an independent Gelco service provider, not a dealer or an authorized agent, and we don’t claim to be factory-trained or certified by Gelco. What we offer is field experience with Gelco caps and tops on Pearland chimneys, not a manufacturer badge.
Yes. We fit OEM-equivalent replacement caps, screens, and mounting hardware when it’s available, and high-grade stainless aftermarket components when it isn’t. We don’t stock genuine Gelco parts and we won’t tell you otherwise. Every part we install is sized to your actual flue opening and sealed properly.
Most Gelco cap work is a single visit, and a straightforward cap replacement with new brackets usually takes well under an hour once the roof access is set up. If we’re also sweeping the flue and running a camera inspection, expect the visit to run longer. We book the work by appointment and tell you the scope before we start.
Gelco Multi-Flue Caps, Gelco Custom Stainless Caps, Gelco Single-Flue Caps, and Gelco Vent Top and Chase Covers. That’s the full range of Gelco products we service in Pearland, and it covers what most local homes actually have on the roof.
Not when the work is done correctly with compatible parts. We document the cap’s condition before and after, use components made for the application, and leave you a record of what was replaced. If a warranty question ever comes up, you’ll have the photos and notes to answer it. Call (866) 361-9474 if you want to talk through your specific situation before we come out.
A Gelco cap cleaning and inspection is typically bundled into a standard chimney sweep visit, and the written estimate sets the final price before any work begins. Cap replacement with new hardware runs more, since it includes the cap and mounting parts. The estimate is free, and we don’t recommend a replacement unless we can show you the metal is failing. Call (866) 361-9474 for an exact quote.
Often the rust decides it. If the spots are surface discoloration and the seams are still tight, the cap can be cleaned, reseated, and sealed. If rust has opened a seam or pitted through the metal, a replacement is the only fix that stops the water. The musty smell after rain is usually the tell that water is getting past the cap and onto the firebox. Call (866) 361-9474 and we’ll look at it before recommending anything.
The cap should cover the flue tile with no visible gap around the edge, and the screen collar should sit flush with the tile. If you can see daylight between the cap skirt and the flue, or the cap wiggles when you nudge it from below, it’s either undersized or loose. Measuring the flue opening is the only reliable check, and we do it as part of the visit.
Yes, screens and spark arrestors are replaceable separately from the cap in most cases. A matted screen is usually a sign the flue was burning poorly or the cap hasn’t been checked in years, so we like to sweep the flue at the same time. That’s the piece that keeps the new screen from clogging again within a season.
It does. The subtropical Gulf humidity keeps metal damp for long stretches, which is what drives seam rust, and storm-season wind is what works brackets and screws loose. Pearland’s mix of newer subdivisions and occasional hard freezes adds another wrinkle: brick and mortar caps crack after a single freeze, and once the crown opens, water gets into the chase and the Gelco cap above it takes the blame. Periodic inspection catches both before they compound.
Cap installation involves roof access and working at height, which is the real risk rather than the fastening itself. An incorrectly sized or poorly sealed cap is also the kind of mistake that doesn’t show up until the next hard rain. We do this on ladders and roofs routinely and can confirm draft and water paths before we leave. Call (866) 361-9474 if you’d rather have it done and documented.
Book Your Gelco Service in Pearland, TX
If you have a Gelco cap, top, or vent component on your chimney and it hasn’t been looked at in a few years, the honest answer is it’s probably due. One call covers sweep, inspection, and repair, and the estimate is free. Call (866) 361-9474. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Pearland Chimney Cleaning.